Siemens SCALANCE XP208EEC Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 96

background image

Safety notices

2

Read the safety notices

Note the following safety notices. These relate to the entire working life of the device.

You should also read the safety notices relating to handling in the individual sections,
particularly in the sections "Installation" and "Connecting up".

CAUTION

To prevent injury, read the manual before use.

NOTICE
Loss of water and dust protection

If you open the device, it loses its water and dust protection.
• Do not open the device.

If the is not adhered to, the manufacturer's guarantee is lost.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD

Do not open the device. There are no serviceable parts inside of the device.

WARNING

EXPLOSION HAZARD

Do not open the device when the supply voltage is turned on.

Safety notices when using the device according to Hazardous Locations (HazLoc)
If you use the device under HazLoc conditions you must also keep to the following safety notices
in addition to the general safety notices for protection against explosion:

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-hazardous
locations only.

This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations only.

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

9

«
...
7
8
9
10
11
...
»

Содержание SCALANCE XP208EEC

































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE XP208EEC

Бренд: Barksdale Страницы: 6

Бренд: 3Com Страницы: 128

Бренд: 3Com Страницы: 2

Бренд: 3Com Страницы: 422

3CR16708-91 - OfficeConnect Managed Switch 9

Бренд: 3Com Страницы: 4

Бренд: 3Com Страницы: 5

Бренд: 3Com Страницы: 30

Бренд: 3Com Страницы: 36

Бренд: 3Com Страницы: 4

Baseline 2226-PWR Plus

Бренд: 3Com Страницы: 77

Бренд: 3Com Страницы: 570

OfficeConnect WX1200

Бренд: 3Com Страницы: 28

Baseline 2226-PWR Plus

Бренд: 3Com Страницы: 4

CoreBuilder 6000

Бренд: 3Com Страницы: 31

Бренд: X10 Страницы: 20

Бренд: FANATEC Страницы: 40

Бренд: Under Control Страницы: 9

Бренд: Comprehensive Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды