Siemens SCALANCE XP208EEC Скачать руководство пользователя страница 17

Страница: 17 / 96

Description of the device

4.1

Product overview

Article numbers

There are two variants of some devices with different article numbers. These variants differ only
in their factory settings. All other properties are identical.

Device

Description

Article number
(Ethernet/IP)

Article number
(PROFINET)

SCALANCE XP208

8 x 10/100 Mbps M12 connector technol‐
ogy electrical

6GK5 208-0HA00-2TS6

6GK5 208-0HA00-2AS6

SCALANCE XP208EEC

8 x 10/100 Mbps M12 connector technol‐
ogy electrical, varnished circuit board

6GK5 208-0HA00-2ES6

SCALANCE XP208PoE EEC

8 x 10/100 Mbps M12 connector technol‐
ogy electrical, varnished circuit board,
Power over Ethernet on 4 ports

6GK5 208-0UA00-5ES6

SCALANCE XP216

12 x 10/100 Mbps and 4 x 10/100/1000
Mbps M12 connector technology electri‐
cal

6GK5 216-0HA00-2TS6

6GK5 216-0HA00-2AS6

SCALANCE XP216EEC

12 x 10/100 Mbps and 4 x 10/100/1000
Mbps M12 connector technology electri‐
cal, varnished circuit board

6GK5 216-0HA00-2ES6

SCALANCE XP216PoE EEC

12 x 10/100 Mbps und 4 x
10/100/1000 Mbps M12 connector tech‐
nology electrical, varnished circuit board,
Power over Ethernet on 8 ports

6GK5 216-0UA00-5ES6

Factory settings

EtherNet/IP variants
• Industrial Ethernet protocol: EtherNet/IP

• Base bridge mode: 802.1Q VLAN Bridge

• Redundancy mechanism: RSTP

• Trust mode: Trust CoS-DSCP

• IGMP Snooping/IGMP Querier: On

• IPv4 Address Collision Detection: Attempt to defend

PROFINET variants
• Industrial Ethernet protocol: PROFINET

• Base bridge mode: 802.1D transparent bridge

SCALANCE XP-200
Operating Instructions, 03/2021, C79000-G8976-C428-08

Содержание SCALANCE XP208EEC

































































































Результаты поиска

Содержание SCALANCE XP208EEC

Отзывы:

Похожие инструкции для SCALANCE XP208EEC

Бренды по названию

Популярные бренды

Siemens SCALANCE XP208EEC, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE XP208EEC

Отзывы:

Похожие инструкции для SCALANCE XP208EEC

Бренды по названию

Популярные бренды