Siemens SCALANCE X-200RNA Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 158

background image

3. Following startup, the correct link status is indicated by the port LEDs after approximately

5 seconds.

4. The SCALANCE X-200RNA (HSR) is now ready for operation.

Note
SCALANCE X204RNA EEC (PRP/HSR)
If the device has not yet been configured, a device error is indicated (red fault LED lit

permanently). This means that no link can be established on the redundancy ports.
In this case, the mode LED also flashes since the operating mode is not defined.

4.8.2.5

Mode LED (SCALANCE X204RNA EEC (PRP/HSR))

The SCALANCE X204RNA EEC (PRP/HSR) has the labeling of both devices on its housing,

in other words, that of the SCALANCE X204RNA EEC (PRP) and the SCALANCE X204RNA

EEC (HSR). Depending on how you configure the SCALANCE X204RNA EEC (PRP/HSR),

the labeling is valid as described in the sections above.
The exception is the mode LED (third LED from the top):
● When the LED is lit, the SCALANCE X204RNA EEC (PRP/HSR) is in HSR mode. This

means that the right-hand labeling of the LED displays applies. The device behaves like a

SCALANCE X204RNA EEC (HSR).

● When the LED is not lit, the SCALANCE X204RNA EEC (PRP/HSR) is in PRP mode. This

means that the left-hand labeling of the LED displays applies. The device behaves like a

SCALANCE X204RNA EEC (PRP).

Descriptions of the products

4.8 LEDs

SCALANCE X-200RNA

Operating Instructions, 10/2016, C79000-G8976-C342-04

53

«
...
51
52
53
54
55
...
»

Содержание SCALANCE X-200RNA































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE X-200RNA

Бренд: Quick Страницы: 28

Бренд: H3C Страницы: 55

Бренд: H3C Страницы: 111

Бренд: H3C Страницы: 34

Бренд: H3C Страницы: 47

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 47

Бренд: H3C Страницы: 4

S5560X-EI Series

Бренд: H3C Страницы: 63

S5560X-EI Series

Бренд: H3C Страницы: 89

Бренд: H3C Страницы: 3

S12500G-AF Series

Бренд: H3C Страницы: 86

Бренд: H3C Страницы: 168

Бренд: H3C Страницы: 56

Бренд: H3C Страницы: 19

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 36

Бренд: ifs Страницы: 352

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды