Siemens SCALANCE X-100 Скачать руководство пользователя страница 38

Страница: 38 / 78

Connecting up

5.3 Signaling contact

SCALANCE X-100

Operating Instructions, 12/2016, A2B00060666-08

5.3

Signaling contact

The signaling contact is connected to a 2-pin plug-in terminal block. The signaling contact

(relay contact) is a floating switch with which error/fault states can be signaled by breaking

the contact.

NOTICE
Damage due to voltage being too high
The signaling contact can be subjected to a maximum load of 100 mA (safety extra-low

voltage SELV, 24 VDC).
Higher voltages or currents can damage the device!

The following figure shows the position of the signaling contacts of the SCALANCE X-100 IE

switches and the assignment of the terminal block.

Pin number

Assignment

Pin 1

Pin 2

The following errors/faults can be signaled by the signaling contact:

●

The failure of a link at a monitored port.

●

The failure of one of the two monitored power supplies.

The connection or disconnection of a communication node on an unmonitored port does not

lead to an error message.
The signaling contact remains activated until the error/fault is eliminated or until the current

status is applied as the new desired status using the button.
When the device is turned off, the signaling contact is always activated (open).

Содержание SCALANCE X-100















































































Результаты поиска

Содержание SCALANCE X-100

Отзывы:

Похожие инструкции для SCALANCE X-100

Бренды по названию

Популярные бренды

Siemens SCALANCE X-100, Руководство по эксплуатации

Результаты поиска

Содержание SCALANCE X-100

Отзывы:

Похожие инструкции для SCALANCE X-100

Бренды по названию

Популярные бренды