Siemens RUGGEDCOM WIN5237 Скачать руководство пользователя страница 39

Страница: 39 / 42

RUGGEDCOM WIN5237

Installation Guide

Chapter 5

Certification

European Union (EU)

Section 5.1.3

European Union (EU)

This subscriber station is declared by Siemens Canada Ltd to comply with essential requirements and other

relevant provisions of the following EU directives:
•

IEC/EN 60950-1

Information Technology Equipment – Safety – Part 1: General Requirements

Section 5.1.4

TÜV Rheinland

This subscriber station is certified by TÜV Rheinland to meet the requirements of the following standards:
•

UL 60950-1:2007 R10.14

Information Technology Equipment – Safety – Part 1: General Requirements

•

UL 60950-22:2007 R12.11

Information Technology Equipment – Safety – Part 22: Equipment to be Installed Outdoors

The subscriber station is marked with a TÜV Rheinland marking and can be used throughout the European

community.

A copy of the TÜV Rheinland Declaration of Conformity is available from Siemens Canada Ltd. For contact

information, refer to

“Contacting Siemens”

Section 5.1.5

ISED

This subscriber station is declared by Siemens Canada Ltd to meet the requirements of the following ISED

(Innovation Science and Economic Development Canada) standard:
•

RSS-197

Wireless Broadband Access Equipment Operating in the Band 3650–3700 MHz

Section 5.1.6

FCC

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 Subpart B and Part 90 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the device is operated in a commercial environment.
This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this device does cause harmful interference

Содержание RUGGEDCOM WIN5237











































Результаты поиска

Содержание RUGGEDCOM WIN5237

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5237

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM WIN5237, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM WIN5237

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5237

Бренды по названию

Популярные бренды