Siemens RUGGEDCOM WIN5237 Скачать руководство пользователя страница 22

Страница: 22 / 42

Chapter 2

Installing the Subscriber Station

RUGGEDCOM WIN5237

Installation Guide

Connecting the RUGGEDCOM WIN1010

Section 2.8.1

Connecting the RUGGEDCOM WIN1010

The RUGGEDCOM WIN1010 is a Power-over-Ethernet injector used to power the subscriber station and distribute

data. The injector provides RJ45 input connectors that include 10/100Base-T transceivers for connection to an IEEE

802.3 (10/100Base-T) compatible device. It receives power from a 100 to 240 VAC power source using an IEC-320-

C14 industry standard connector.

CAUTION!

Electrical hazard – risk of damage to equipment. The power cord provided with the data adapter is

safety certified according to national rules. Do not use a power cord that has not been approved by

Siemens for use with the data adapter.

To connect power and data to the subscriber station, do the following:

CAUTION!

Crushing hazard – risk of damage to equipment. Route all power supply cables so that people cannot

walk on them or place objects on or against them. This can pinch or damage the cords.

1. Connect an indoor-to-outdoor CAT-5e cable to the Ethernet port on the injector. For information on cable

requirements, refer to

Section 3.5, “IDU to ODU Cable Specifications”

2. Apply the PoE connector kit to the other end of the CAT-5e cable. For more information, refer to

Section 2.8.3, “Assembling the PoE Connector”

3. Connect the modified end of the cable to the

DC/ETH

port on the subscriber station.

Figure 6: Connecting the RUGGEDCOM WIN1010 PoE Injector

Subscriber Station

PoE Cable

Switch or Router

Ethernet

RUGGEDCOM WIN1010

AC Power Cable

AC Power

4. Connect a CAT-5e cable between the RUGGEDCOM WIN1010 and a 10/100Base-T port of a switch or router.
5. Make sure all system components are properly installed and all cable connectors are securely positioned in

the appropriate ports.

6. Connect the data adapter to the 110/220 VAC mains.

Содержание RUGGEDCOM WIN5237











































Результаты поиска

Содержание RUGGEDCOM WIN5237

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5237

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM WIN5237, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM WIN5237

Отзывы:

Похожие инструкции для RUGGEDCOM WIN5237

Бренды по названию

Популярные бренды