Siemens RUGGEDCOM RX1000 Скачать руководство пользователя страница 16

Страница: 16 / 50

Chapter 2

Installing the Device

RUGGEDCOM RX1000

Installation Guide

Connecting DC Power

Figure 5: Terminal Block Wiring

Screw-Type Terminal Block

Pluggable Terminal Block

Jumper

Positive/Live (+/L) Terminal

Negative/Neutral (-/N)

Terminal

Surge Ground Terminal

Chassis Ground Terminal

4. Connect the negative wire from the power source to the negative/neutral (-/N) terminal on the terminal block.

For more information, refer to

Section 2.2.3, “Wiring Examples”

5. Install the supplied metal jumper between terminals 2, 4 and 6 to connect the surge ground terminals to the

chassis ground terminal. The surge ground terminals are used as the ground conductor for all surge and

transient suppression circuitry internal to the unit.

6. Connect the ground terminal on the power source to the chassis ground terminal on the device. For more

information, refer to

Section 2.4, “Grounding the Device”

DANGER!

Electrocution hazard – risk of death, serious personal injury and/or damage to the device. Make

sure the supplied terminal block cover is always installed before the device is powered.

7. Install the terminal block cover.

Section 2.2.2

Connecting DC Power

To connect a high or low DC power supply to the device, do the following:

CAUTION!

Electrical hazard – risk of damage to equipment. Before testing the dielectric strength (HIPOT) in the

field, remove the metal jumper. This metal jumper connects transient suppression circuitry to chassis

ground and must be removed in order to avoid damage to transient suppression circuitry during testing.

NOTE

The terminal block is divided into separate terminals for each internal power supply. Make sure to

connect the external power supply to the appropriate terminals.

Содержание RUGGEDCOM RX1000



















































Результаты поиска

Содержание RUGGEDCOM RX1000

Отзывы:

Похожие инструкции для RUGGEDCOM RX1000

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RX1000, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RX1000

Отзывы:

Похожие инструкции для RUGGEDCOM RX1000

Бренды по названию

Популярные бренды