manualshive.com logo in svg

Siemens RUGGEDCOM RS900F, Руководство по установке

Поделиться
Скачать
Siemens RUGGEDCOM RS900F Скачать руководство пользователя страница 22

Chapter 2

Installing the Device

RUGGEDCOM RS900F

Installation Guide

12

Connecting the Failsafe Alarm Relay

2

1

2

1

Figure 4: Panel Mounting

1.

 Screw   

 

2.

 Panel Mount Adapter

3. Secure the adapters to the panel with #6-32 screws.

Section 2.5

Connecting the Failsafe Alarm Relay

The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is closed

when the unit is powered and there are no active alarms. If the device is not powered or if an active alarm is

configured, the relay opens the NO contact and closes the NC (Normally Closed) contact.

NOTE

Control of the failsafe relay output is configurable through ROS-F. One common application for this

relay is to signal an alarm if a power failure occurs. For more information, refer to the ROS-F User

Guide for the RUGGEDCOM RS900F.

To connect the failsafe alarm relay, do the following:
1. Insert the failsafe alarm relay terminal block into the device and tighten the screws.
2. Connect a failsafe device to the terminal block.

Содержание RUGGEDCOM RS900F

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды