manualshive.com logo in svg

Siemens RUGGEDCOM RS900F, Руководство по установке

Поделиться
Скачать
Siemens RUGGEDCOM RS900F Скачать руководство пользователя страница 19

RUGGEDCOM RS900F

Installation Guide

Chapter 2

Installing the Device

Mounting the Device

9

60079-0 and CSA/UL/IEC/EN 60079-15. The enclosure shall have a minimum service temperature range of -40 to

100 °C (-40 to 212 °F).

• The equipment shall be used in an area of not more than pollution degree 2 as defined in IEC/EN 60664-1.
• The serial DB9 console port shall only be used in the safe area.
• The equipment must be appropriately connected to safety Earth upon installation.

NOTE

For further details of the device's compliance with Class I, Division 2, Zone 2 standards, refer to

Section 6.1, “Approvals”

.

IMPORTANT!

Do not disconnect or open equipment unless power has been switched off or the area is known to be

non-hazardous.

IMPORTANT !

Débrancher ou ouvrir l'équipment seulement si l'alimnetation a été coupée ou si l'on sait que la zone

ne pose aucun danger.

IMPORTANT!

Substitution of the components may impair suitability for Class I, Division 2.

IMPORTANT !

Le remplacement de composants pourrait compromettre l'admissibilité à la Classe I, Division 2.

Sample Hazardous Location Label

The following is an example of the RUGGEDCOM RS900F hazardous location label:

Figure 2: Compliance Label (Example)

Section 2.4

Mounting the Device

The RUGGEDCOM RS900F is designed for maximum mounting and display flexibility. It can be equipped with

adapters that allow it to be installed on a 35 mm (1.4 in) DIN rail or affixed to a panel.

Содержание RUGGEDCOM RS900F

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды