Siemens RUGGEDCOM i803 Скачать руководство пользователя

Страница: 34 / 40

Certification

The RUGGEDCOM i803 device has been thoroughly tested to guarantee its

conformance with recognized standards and has received approval from recognized

regulatory agencies.

6.1

Approvals

This section details the standards to which the RUGGEDCOM i803 complies.

6.1.1

CSA

This device meets the requirements of the following Canadian Standards Association

(CSA) standards under certificates 2058468 (general safety) and 2068170

(hazardous locations):
•

CAN/CSA-C22.2 No. 62368-1-14

Information Technology Equipment – Safety – Part 1: General Requirements

•

CAN/CSA-C22.2 No. 0-M91

General Requirements - Canadian Electrical Code, Part II

•

CAN/CSA-C22.2 No. 14-05

Industrial Control Equipment

•

CAN/CSA-C22.2 No. 142-M1987

Process Control Equipment Industrial Products

•

CAN/CSA-C22.2 No. 213-M1987

Non-Incendive Electrical Equipment for Use in Class I, Division 2 Hazardous

Locations

•

UL 62368-1

Information Technology Equipment – Safety Part 1: General Requirements

•

ANSI/UL 508

Standard for Industrial Control Equipment

•

UL 916 4th Edition 2007

Standard for Energy Management Equipment

RUGGEDCOM i803

Installation Manual, 04/2022, C79000-G8976-1005-07

Содержание RUGGEDCOM i803









































Результаты поиска

Содержание RUGGEDCOM i803

Отзывы:

Похожие инструкции для RUGGEDCOM i803

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM i803, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM i803

Отзывы:

Похожие инструкции для RUGGEDCOM i803

Бренды по названию

Популярные бренды