background image

Introduction

1

The RUGGEDCOM i803 is a compact, fully managed Ethernet switch designed to

operate reliably in harsh industrial environments. The flexibility of the RUGGEDCOM

i803 allows the user to choose from managed or unmanaged, regular or extended

temperature, fiber optical or copper interfaces, and fast or Gigabit Ethernet. With

up to nine Ethernet ports, the RUGGEDCOM i803 is the perfect choice for a wide

variety of demanding industrial environments such as those found in process control

applications (oil and gas, petro-chemical, metals and mining, wind farms).
The RUGGEDCOM i803 is packaged in a compact, die cast aluminum, DIN mountable

enclosure for efficient use of cabinet space. Dual 24 VDC power inputs increase

reliability in case of primary power supply faults. The i800 provides a high level of

immunity to electromagnetic interference and heavy electrical surges typical of

environments found in industrial applications. An operating temperature range of

-20 to 60 °C (-4 to 140 °F) or optionally -40 to 85 °C (-40 to 185 °F), coupled with

hazardous location certification (Class 1 Division 2) allows the RUGGEDCOM i803 to

be placed in almost any location.
The RUGGEDCOM i803 features a full array of intelligent functionality for high

network availability and manageability. The embedded Rugged Operating System

(ROS) provides advanced Layer 2 and Layer 3 networking functions, and advanced

cyber security features. The Enhanced Rapid Spanning Tree Protocol (eRSTP) provides

very fast network recovery in case of failures, guaranteeing a high availability

network, and allows any topology from ring to mesh. Numerous other features

like VLANs and QoS make the RUGGEDCOM i803 an enterprise class switch in an

industrial class package.

1.1

Feature Highlights

Ethernet Ports

• Up to 4 x 10/100Base-TX ports
• Up to 2 x 100Base-FX port
• 2 x 1000Base-LX ports
• Industry standard LC fiber optical connectors
• Multi-mode and single-mode optical transceivers

Cyber Security Features

• Multi-level user passwords
• SSH/SSL (128-bit encryption)
• Enable/disable ports, MAC based port security

RUGGEDCOM i803

Installation Manual, 04/2022, C79000-G8976-1005-07

1

Содержание RUGGEDCOM i803









































Отзывы: