manualshive.com logo in svg

Siemens RDG200KN, Основная документация, Страница: 6 / 150

Поделиться
Скачать
Siemens RDG200KN Скачать руководство пользователя страница 6

About this document
Before you start

1

6 | 150

A6V11545892_en--_a

1.3 Before you start

1.3.1 Trademarks

The table below lists the third-party trademarks used in this document and their

legal owners. The use of trademarks is subject to international and domestic

provisions of the law.

Trademarks

Legal owner

Synco

TM

Android

TM

Google Inc.

All product names listed in the table are registered (®) or not registered (™)

trademarks of the owner listed in the table. We forgo the labeling (e.g. using the

symbols ® and ™) of trademarks for the purposes of legibility based on the

reference in this section.

1.3.2 Copyright

This document may be duplicated and distributed only with the express permission

of Siemens, and may be passed only to authorized persons or companies with the

required technical knowledge.

1.3.3 Quality assurance

This document is prepared with great care.

●

The contents of this document are checked at regular intervals.

●

Any corrections necessary are included in subsequent versions.

●

Documents are automatically amended as a consequence of modifications and

corrections to the products described.

Please make sure that you are aware of the latest document revision date.
If you find lack of clarity while using this document, or if you have any criticisms or

suggestions, please contact the Product Manager in your nearest branch office.

The addresses of the Siemens Regional Companies are available at

www.buildingtechnologies.siemens.com

.

Содержание RDG200KN























































































































































Отзывы:

Нет отзывов