Siemens POWERMOBIL Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 36

Siemens POWERMOBIL Скачать руководство пользователя страница 29

Installation

3 - 9

Siemens AG

SPR2-240.841.01

Page 9 of 10

POWERMOBIL

Medical Solutions

Rev. 01

05.03

CS PS 24

Cables for basic unit

3

•

Insert the cables in the energy chain. Make sure that cables do not intersect.

•

Fasten both cables for the cable module using cable clamps (1/Fig. 21).

•

Close the energy chain.

•

Secure the last link on both ends of the energy chain using cable ties or insulation tape to
avoid accidental opening.

•

Attach the ferrite core to the cable with the plug M2. X1 (1 turn around the ferrite core).
Connect the plug.

•

Attach the connection cable for the inverter. Tighten the nuts with a torque of 4.8 Nm.
Fasten the cable using a cable clamp. Make sure that the shielding makes good ground
contact.

•

Fasten the protective ground wires.

•

Attach the Plexiglas cover (4/Fig. 21).

•

Reconnect the BNC plug for the coaxial cable.

•

Insert the previously ejected contacts of the plug D30 X3 in the connector housing, as
previously noted.

•

Run the cables with their plugs to the corresponding plug connections / PC boards ac-
cording to labeling. Fix the cables using cable ties.

•

Tie the cables close to the lifting column using cable ties in such a way that they do not
rub against any moving parts or are crushed when moving the lifting column.

•

Fix all cables to the cable holder (1/Fig. 21) using cable ties.

•

Reattach all shielded cables using the provided cable clamps. Make sure that the shield-
ing makes good contact (2/Fig. 21) (1/Fig. 22).

Fig. 21

Fig. 22

t

«
...
27
28
29
30
31
...
»

Содержание POWERMOBIL





































Отзывы:

Нет отзывов