Siemens POWERMOBIL SP Скачать руководство пользователя страница 31

Страница: 31 / 44

Siemens AG

SPR2-240.831.01.02.02

POWERMOBIL

07.05

CS PS 24

Safety Inspection

Page 31 of 44

Medical Solutions

3.2 Electrical

safety

SIE

Cables and plugs

•

Check visible system cables and plugs for damage.

SIE

Check of the POWERPHOS power inverter line

•

Remove the cover of the POWERPHOS.

•

Tighten the contact screws X7 and X9 with a torque of 4.8 Nm.

•

Re-attach the cover and seal with sealing compound.

NOTE

Check the function of the fan before attaching the cover.

See

(Maintenance / p. 36)

POWERPHOS fan.

•

Reattach the cover.

SIE

Fluoroscopic timer

•

Check: See section on "Compulsory radiation switch off".

SIE

Audible warning signal

•

Check: See section on "Compulsory radiation switch off".

SIE

Radiation indicators

•

Check: See section on "Compulsory radiation switch off".

SIE

Radiation release switch

•

Check: See section on "Compulsory radiation switch off".

SIE

Compulsory radiation switch off

Test the functioning of the audible warning signal and compulsory radiation switch off (if
required) according to the country-specific regulations. Also perform the following
checks:

•

Release fluoroscopy for one minute. Use a wristwatch to check the proper functioning
of the fluoroscopic timer.

•

All radiation indicators on the system operating console and monitor trolley must illumi-
nate during fluoroscopy release.

•

Check the function of the radiation release switches (hand and foot switches).

•

Check the radiation release switches for damage.

•

Check the cables of the hand and foot switches for mechanical damage.

•

Move the the cables of the hand and foot switches to check for breaks and short cir-
cuits.

SIE

Dose rate

•

Switch the system on

•

Check the dose rate (see the POWERMOBIL service instructions for this purpose).

Содержание POWERMOBIL SP













































Результаты поиска

Содержание POWERMOBIL SP

Отзывы:

Похожие инструкции для POWERMOBIL SP

Бренды по названию

Популярные бренды

Siemens POWERMOBIL SP, Инструкция по обслуживанию

Результаты поиска

Содержание POWERMOBIL SP

Отзывы:

Похожие инструкции для POWERMOBIL SP

Бренды по названию

Популярные бренды