Siemens POLYMOBIL Plus Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 50

Siemens POLYMOBIL Plus Скачать руководство пользователя страница 18

POLYMOBIL Plus

SPR8-125.061.02

Page 2 of 4

Siemens AG

Rev. 01

01.00

TD SD 24

Medical Engineering

3 - 2

Troubleshooting

Troubleshooting after error messages

3

Err 1

Capacitor charge error

- Has the system not been used for a longer period of time

(higher capacitor leakage current)?

➪

If the error occurs after switching the system off and back
on again, configure the capacitor bank
(refer to the "Service program" chapter, pages 4-2).

- Are the discharge resistors permanently connected?
- Has the temperature sensor on D950 responded

(D950 TP ’TP’)?

- Has overvoltage in the C-bank been detected? (D950 TP ’VC’)
- Is there a short on D950? The error appears only when the short circuit is

continuous.

Replace D950.

Err 2

+ 15 V - Error

- Check the fuse on power supply U1.
- Is power supply U1 defective?

Err 3

Vfil < Vstby (none or insufficient filament current)

- Do ’V1’ (-DC) and ’V2’ (+DC) flash on D925? Otherwise check fuse F6.
- No filament frequency? Check D915 .
- Connection D925 =>X-ray tube unit (X5).
- ConnectionD925 => D915 (X11).
- Check X-ray tube assembly.
- D925 defective.

Err 4

Vfil > Vstby (filament current is too high)

- Do ’V1’ (-DC) and ’V2’ (+DC) flash on D925? Otherwise check fuse F6.
- Filament frequency too high?
- A/D converter on D915 defective? => Replace D915.
- Short-circuit at the output of the filament inverter =>check connection to/in

the X-ray tube assembly.

Err 5

KVact 0

- No connection to the single tank generator (D915 X8)?
- Plug-in connection on D900 in the single tank generator ok?

Err 6

mAact 0

- Error in the measurement acquisition on D915? => Replace D915 .
- No connection to the single tank generator (D915 X8)?
- Plug-in connection on D900 in the single tank generator ok?

Err 7

Rot 0

(rotating anode speed 0)

- Error on D915 or D925.

≠

≠

≠

≠

«
...
16
17
18
19
20
...
»

Содержание POLYMOBIL Plus



















































Отзывы:

Нет отзывов