Siemens NK8237 IEC 60870-5-104 Скачать руководство пользователя страница 76

Страница: 76 / 80

Maintenance and diagnostics
Correcting communication failures

76
Building Technologies

A6V10854379_a_en

CPS Fire Safety

25.01.2019

Configuring logging function on the fly

Note: The reset of the unit results in restoring the original logging configuration

saved in Composer.

11.3

Correcting communication failures

11.3.1

IEC communication problems

Communication faults on the IEC may depend on different causes. The problem

can occur in the NK8237 unit or in the connections.

Check the NK8237

Check power, vital function, and diagnostic state of the corresponding LED located

on the front panel.

Note: If you need to modify the IP address because of a network change, you

might want to reset the device back to factory configuration by setting DIP-switch

1 or 2 to ON (see

Internal DIP switches [➙

17]) and then connect using the known

address to change the IP address.

Check the network connections (IEC TCP/IP)

⚫

LAN

Diagnostic information about the LAN state can be obtained from different

layers:

Link state LED of Repeater or Ethernet adapters gives you information about

the physical connection and the speed of the Ethernet link.

1) Select Start > Programs > Accessories > Command Prompt.

2) Choose from the following commands:

Содержание NK8237 IEC 60870-5-104

















































































Результаты поиска

Содержание NK8237 IEC 60870-5-104

Отзывы:

Похожие инструкции для NK8237 IEC 60870-5-104

Бренды по названию

Популярные бренды

Siemens NK8237 IEC 60870-5-104, Установка, настройка и ввод в эксплуатацию

Результаты поиска

Содержание NK8237 IEC 60870-5-104

Отзывы:

Похожие инструкции для NK8237 IEC 60870-5-104

Бренды по названию

Популярные бренды