Siemens MK8000 MP4.30 Скачать руководство пользователя страница 91

Страница: 91 / 92

Tips for Integrating with an OPC client

Building Technologies

048_DMS_MK8000_ICC_MP4.30_A6V10062407_a_en

Fire Safety & Security Products

06.2010

Appendix B.

Enabling & disabling MK8000 auto-start

During normal use of the MK8000, it is convenient to have the MK8000 server start
automatically upon system start-up. During troubleshooting and system testing,
however, it may be more convenient to disable auto start.

Changing the auto start settings

To change the auto start settings, do the following:

Open the services menu (Start



Settings



Control Panel



Administrative

Tools



Services).

Select DixieSystem Supervisor.

Right-click DixieSystem Supervisor to display the Properties pop-up window.

Select one of the options available in the Startup type drop-down menu in the
General tab.

Fig. 92 Change auto-start settings for the MK8000 server

Содержание MK8000 MP4.30





























































































Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды

Siemens MK8000 MP4.30, Руководство по установке и настройке

Результаты поиска

Содержание MK8000 MP4.30

Отзывы:

Похожие инструкции для MK8000 MP4.30

Бренды по названию

Популярные бренды