manualshive.com logo in svg

Siemens M20 Terminal, Техническое описание

Поделиться
Скачать
Siemens M20 Terminal Скачать руководство пользователя страница 169

Application notes

Version 8 dated 15.03.00

169

Siemens Information and Communication Products

A

8.2.8

Phone call

1

8.2.8.1

Mobile originated call

8.2.8.2

Redial a number

8.2.8.3

Incoming call

8.2.8.4

Call a number stored in a phonebook

8.2.9

Data transfer

1.  If not specifically mentioned, finish your commands with ENTER.

atd015265241;

Dial the number you want to be connected with (always with dialling code)

_

You see the cursor while the called party’s phone is ringing

CONNECT

Your call is answered

NO CARRIER 

Your partner has hung up

ath

To end the connection before your partner

If your call is not answered:

_

the cursor disappears after some time

NO CARRIER 

ATDL;

The phone number last called is dialled again

CONNECT

....

RING

Somebody calls you

ata

”Pick up the receiver” 

atd>3;

Rings up number 3 of your current phonebook

CONNECT

....

atd>”SM”,3;

If you want to use a phonebook, different from the current one

CONNECT

....

atd015265241

Dial the number you want to be connected with (always with dialling co-
de)

NOTE

: do not use a semicolon at the end of the command

_

You see the cursor while the other’s phone is ringing

connect 9600

Your call is answered, the transfer rate is 9600 bit/s

.....

You exchange data

+++

〈

pause

〉

Switches from transparent to command mode

Though the phone connection is still active, characters are no longer trans-
ferred to the other modem

ato

Returns to transparent mode

Содержание M20 Terminal











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды