Siemens LITHOSTAR Multiline SP Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 54

background image

Start-Up of Multiline System

4 - 3

Siemens AG

RXL2-120.815.01

Page 3 of 8

LITHOSTAR Multiline

Medical Solutions

Rev. 02

02.05

CS PS 24

System manual

Generator Programming

4

The generator was programmed in the factory. The values cannot be changed.

Generator start-up is performed in the ”Components-POLYDOROS -Adjustment” menu.

Setting the Time and Date

4

Set the time and date according to the Start-Up Instructions for POLYDOROS configured
with LITHOSTAR Multiline ”Generator Configuration with the Service PC”,
RXL2- 20.034.02..., prior to Logon in the sequence "System - Connect - Real-time".
Subsequently, click "Put to Unit".

Performing test shots from the X-ray Tube

4

•

Perform the Warm-Up, Pre-Heating, Filament Correction and Filament Push Current
functions according to the Instructions "System Congifuration" RXL2-120.034...

The following provides a summary of these instructions.

XCS Software VE00J (POLYDOROS SX) or VD00A (POLYDOROS LX) and the
Videomed Service Software VA01A must be installed on the service PC.

•

Connect the service PC to the generator.

•

Call the Software Manager in the Program Manager.

•

Mark the required version (according to generator).

•

Select the "Make to current version" button.

•

Terminate the Software Manager with "Exit".

•

Call the XCS service software.

•

Perform user identification and enter user name.

•

Enter the Group ID:

_Siemens

.

•

Click OK.

•

Select "System Terminal Setting and Connect: 19200 or 9600" for the Baud rate.

•

Click Login.

•

Confirm the message "Adjusting and/or configuration ..." with OK.

•

Call up POLYDOROS in the Components menu.

•

Switch S3/X44 on.

•

Confirm the query "Set the S3/X44 switch ...", with OK. The green LED V90 on D100
lights up (Refer to Fig.1)

•

Select "Generator Parameters" in the Adjustment menu.

•

Select "24" m for the Tube 1 High Tension Cable Length in the Generator Parameters
field.

•

Select "Fluoroscopy" in the "Warm Up" menu.

«
...
21
22
23
24
25
...
»

Содержание LITHOSTAR Multiline SP























































Отзывы:

Нет отзывов

Похожие инструкции для LITHOSTAR Multiline SP

Бренд: CAIRE Страницы: 2

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Dynapro ET 355 Monitor HL

Бренд: 3M Страницы: 23

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: GE Страницы: 212

Бренд: ICP DAS USA Страницы: 45

Бренд: Raytheon Страницы: 68

Бренд: KegLand Страницы: 23

ST70 Instrument

Бренд: Raymarine Страницы: 12

Бренд: Raven Страницы: 73

Бренд: Tascam Страницы: 3

Бренд: RAB Lighting Страницы: 4

Бренд: campgo Страницы: 33

Бренд: Teac Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды