Siemens KMS Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 89

background image

BA 9137 en 12/2015

10.3.1

Replacing the air filter cartridge

Note

Annually

or when the air filter is heavily soiled.

•

Remove the air filter cover and replace the filter element (cleaning of the paper filter is not possible).

10.4

Flushing

It must generally be distinguished between "flushing during the initial start-up" and "flushing before or after
repair work".

Flushing before or after repair work serves for removal of soiling (e.g. bon deposits, oil foam, abraded
material) and must be conducted depending on the scope of the repair.

Flushing should be carried out with the selected service lubricating oil. In general, lower viscosities
(e.g. VG 46 or VG 100) should be used for the flushing oil that is of the same brand as the oil type chosen
as the operating oil.

•

For flushing-oil quantity see item 7.1.4.1.

•

Flushing times:
For flushing, operate the oil pump of the low-pressure lubricating circuit for at least 6 hours.

NOTICE

Property damage

Damage to the gear unit and the oil-supply system is possible from soiling of the oil.
After flushing, the oil must be carefully drained off through the oil drain cocks
(see Figure 7 in item 7.1.3) on the gear unit and the oil-supply system. It may be re-used only as
flushing oil. Clean the flushing oil before re-use. The flushing oil must be filtered beforehand or during
filling using a nominal filter mesh of 25 μm (0.0010 inch).
The flushing oil can be reused for a maximum of 6 flushing operations.

Note

If the oil tends to increasing foaming during flushing, we recommend having the oil analysed by the oil
supplier as to its suitability for use.

10.5

Oil filling

NOTICE

Property damage

Damage to the gear unit and oil-supply system is possible.
Fill the gear unit with oil after flushing and before the start-up of the gear unit.

Information on the type, viscosity and required quantity of the oil is given on the rating plate on the gear unit
and/or in the documentation included in the delivery.
The BA 7300 instructions manual relating to the gear unit lubrication and Table "T 7300" containing the
current lubricant recommendations of Siemens can also be consulted on the internet (see back cover).

«
...
74
75
76
77
78
...
»

Содержание KMS


























































































Отзывы:

Нет отзывов

Похожие инструкции для KMS

Бренд: SAMCHULLY Страницы: 48

Бренд: Hagie Страницы: 141

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Varytec Страницы: 5

Бренд: Saab Страницы: 98

Бренд: Kaixin Страницы: 89

Бренд: ZOLL Страницы: 37

Бренд: Wacker Neuson Страницы: 34

Бренд: Wagan Страницы: 4

Бренд: Wachs Страницы: 22

Бренд: Yamaha Страницы: 31

SeQual Eclipse 5

Бренд: CAIRE Страницы: 2

Бренд: Metrohm Страницы: 42

Бренд: Maquet Страницы: 232

Бренд: K-SPORT Страницы: 5

Бренд: Brillion Страницы: 56

Einthoven CR1000

Бренд: ACE Solution Страницы: 29

Tracer DO PockeTester

Бренд: LaMotte Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды