Siemens KMS Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 89

background image

BA 9137 en 12/2015

DANGER

Electrostatic discharge

Danger to life from ignition of present explosive atmosphere by electrostatic discharge.
The coating must not carry an electrostatic charge.
The operator must ensure that highly effective mechanisms which can set up a charge in the coating
are safely avoided.

•

Removed safeguards must be refitted prior to starting up.

•

Notices attached to the gear unit, such as rating plate and direction arrow, must always be observed.
They must be kept free from dirt and paint at all times. Missing plates must be replaced.

•

Screws which have been damaged during assembly or disassembly work must be replaced with new
screws of the same strength class and type.

•

Spare parts must be obtained from Siemens (see section 11. "Spare parts, customer service").

3.2

Special dangers and personal protective equipment

Depending on operating conditions, the surface of the gear unit may develop extreme temperatures.

WARNING

Risk of burns

Serious injury caused by burns on hot surfaces (> 55 °C) is possible.
Wear suitable protection gloves and protection clothing.

WARNING

Risk of low temperatures

Serious injury from cold damage (pain, numbness, frostbites) on cold surfaces (< 0 °C) is possible.
Wear suitable protection gloves and protection clothing.

WARNING

Risk of scalding

Serious injury from discharging hot operating media is possible when these are changed.
Wear suitable protection gloves, protection glasses and protection clothing.

WARNING

Risk of eye injury

Small foreign matter such as sand or dust can get into the cover plates of the rotating parts and might
be thrown back by these.
Wear suitable protective glasses.

«
...
11
12
13
14
15
...
»

Содержание KMS


























































































Отзывы:

Нет отзывов

Похожие инструкции для KMS

Бренд: Rangevision Страницы: 31

Бренд: GE Страницы: 698

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Бренд: Taylor-Wharton Страницы: 25

Бренд: i-CAT Страницы: 96

Бренд: Pari Страницы: 50

Бренд: Icare Страницы: 42

Бренд: YMC Страницы: 49

Бренд: Octane Fitness Страницы: 8

Бренд: Octane Fitness Страницы: 10

Бренд: OCENCO Страницы: 48

Бренд: Ocean Optics Страницы: 6

Бренд: Kellfri Страницы: 44

Бренд: ebm-papst Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды