Siemens INOX PRO SIMATIC IFP1900 Скачать руководство пользователя страница 23

Страница: 23 / 25

SIMATIC IPC277D/E 19" INOX PRO, SIMATIC IFP1900 INOX PRO
Service Manual, 11/2017, A5E35751762-AC

Accessories and spare parts

Accessories

Mounting kit for stand mounting
A mounting kit is available for stand mounting of the device. Mounting kit contents:

●

1 stainless steel tube with flange: Length 500 mm, outer diameter 48.3 mm,

inner diameter 40 mm.

The mechanical interface of the stainless steel tube with flange fits the mechanical

interface of the device.

●

4 hexagon screws M5×25 made of stainless steel

●

1 flat seal

Article number 6AV7675-1GB00-0AA0

Mounting kit for support arm mounting
A mounting kit is available for support arm mounting of the device. Mounting kit contents:

●

1 stainless steel tube with flange: Length 500 mm, outer diameter 48.3 mm, inner

diameter 40 mm.

The mechanical interface of the stainless steel tube with flange fits the mechanical

interface of the device.

●

1 adapter support arm

●

8 hexagon screws M5×20 made of stainless steel

●

2 flat seals

Article number 6AV7675-1GB10-0AA0

Service pack
The service pack contains:

●

1 spare seal for the connection compartment cover of the device

●

6 screws for the connection compartment cover of the device

●

1 spare seal for the mechanical interface of the device

●

4 screws for fastening the stainless steel tube with flange from a mounting kit to the

mechanical interface of the device

●

1 connecting terminal for the power supply

●

1 terminal block for the terminal strip in the connection compartment

●

Documentation

Article number 6AV7675-1JD20-0AA0

Содержание INOX PRO SIMATIC IFP1900


























Результаты поиска

Содержание INOX PRO SIMATIC IFP1900

Отзывы:

Похожие инструкции для INOX PRO SIMATIC IFP1900

Бренды по названию

Популярные бренды

Siemens INOX PRO SIMATIC IFP1900, Руководство по обслуживанию

Результаты поиска

Содержание INOX PRO SIMATIC IFP1900

Отзывы:

Похожие инструкции для INOX PRO SIMATIC IFP1900

Бренды по названию

Популярные бренды