manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 51

 

Assignment planning 

 

3.6 Configuring the electrical structure 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

49

 

Rules on the Power Consumption and Power Loss of an ET 200M 

For their operation, the S7-300 modules use the necessary power from the backplane bus as 

well as, if necessary, from an external load power supply.  
●

 

The current consumption of all signal modules from the backplane bus must not exceed 

the electrical output that the IM 153-x can supply to the backplane bus. 

●

 

The PS 307 power supply is dependent on the current consumption from the 24 V load 

power supply; this is the result of the total of the current consumption of the signal 

modules and all other connected loads. 

●

 

The power loss of all the components in a cabinet must not exceed the maximum thermal 

rating of the cabinet. 
Tip:When establishing the required dimensions of the cabinet, ensure that the 

temperature inside the cabinet does not exceed the permissible 60°C even where 

external temperatures are high 

You will find the values for the power consumption and power loss of a module under the 

technical specifications of the relevant modules. 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды