Siemens IM 153-4 PN Скачать руководство пользователя страница 243

Страница: 243 / 274

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

241

Compatibilities between the IM 153-x

This chapter includes the most important information that you must know if you are

"changing over" from an old IM 153-x to a new or different IM 153-x.

A.1

Compatibilities between the versions of IM 153 and IM 153-1

The versions of IM 153-1

Table A- 1

Properties and variants of the IM 153-1

Interface module with order number

6ES7153-1AA..

Functions / properties

Min_slave_interval between two slave list cycles

1 ms

0,1 ms

SYNC, FREEZE

–

Module change during operation

–

Direct data exchange

–

as of E07

as of E06

Enhanced diagnostics

•

64 byte diagnostic frame

–

as of E02

–

Extended range of environmental conditions

(outdoors)

–

RC network with 10 MΩ for unearthed configuration

(1 MΩ)

as of E08

as of E07

DPV1-mode

–

as of E05

–

as of E03

E = module version

Compatibility between 153-1AA00- and 153-1AA01-…

The IM 153-1, order number 6ES7153-1AA01-0XB0 is partially upwards compatible. This

means that the configuration and the user programs for the IM 153-1, order number

6ES7153-1AA01-0XB0 can also be used for the IM 153, order number

6ES7153-1AA00-0XB0, apart from if you are working with SYNC and FREEZE in these user

programs. Note also the different min_slave-intervals (refer to table above).

Retrofitting to 153 1AA02 ...

The IM 153-1 with order number 6ES7153-1AA01-0XB0 can be retrofitted to the IM 153-1

with order number 6ES7153-1AA02-0XB0.
Contact your Siemens representative for this.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды