manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 202

Interrupt, error and system messages 

 

9.1 PROFIBUS DP 

 

ET 200M 

200

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

9.1.3.8

 

Channel-specific diagnostics 

Definition 

The channel-related diagnosis gives information about channel errors of modules and 

represents detailed information for the identifier-related diagnosis. 
The channel-related diagnosis starts according to the module status or the H status. 
The channel-related diagnosis does not influence the module status. 
Important: the diagnostic interrupt must be switched on for each module!  

Channel-releated diagnostics 

The channel-related diagnosis is then included in the diagnostic frame only if you have 

enabled "enhanced diagnosis" in the configuration. The maximum number of channel-related 

diagnoses is restricted by the maximum overall length of the slave diagnosis of 64 bytes with 

IM 153-1 or 96 bytes with IM 153-2. The length of the slave diagnosis depends on the 

number of current channel-specific diagnosis.  
Tip: If, when configuring the ET 200M, you block the interrupts, then up to 29 bytes interrupt 

part is also available for the channel-related diagnoses. 

 

 

Note 
Errors that affect all the channels of a module (e.g. the supply voltage of the module fails) 

will be portrayed in the channel-related diagnosis only on channel 0. 
This then reduces the number of channel-related diagnoses and prevents a "diagnostic 

overflow". 

 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды