Siemens IM 153-4 PN Скачать руководство пользователя страница 201

Страница: 201 / 274

Interrupt, error and system messages

9.1 PROFIBUS DP

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

199

9.1.3.7

Module status

Definition

The module status reflects the status of the configured modules and represents a detailed

ID-specific diagnosis with respect to the configuration. The module status starts with the

diagnostics and consists of a maximum of 7 bytes.
The module status is then only included in the diagnostic frame if you have enabled

"enhanced diagnosis" in the configuration.

Module status

The module status for the ET 200M is structured as follows:

%\WH

/HQJWKRIWKHPRGXOHVWDWXVLQFOXGLQJE\WH E\WHV

&RGHIRUGHYLFHUHODWHGGLDJQRVWLFV

6WDWXVW\SH0RGXOHVWDWXV

0RGXOHVWDWXV

&RGHIRUVWDWXVPHVVDJH

$OZD\V

0RGXOHRQVORW

QRPRGXOHLQYDOLGGDWD

LQFRUUHFWPRGXOHLQYDOLGGDWD

0RGXOHIDXOWLQYDOLGGDWDPRGXOH

GHIHFWLYH

0RGXOHRNYDOLGGDWD

Figure 9-5

Configuration of the module status for the ET 200M

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды