Siemens HR478G5.6S, Руководство пользователя и инструкции по установке

Страница: 15 / 44

Time-setting options
en
15
The timer duration can be set in 30-second incre-
ments up to 10 minutes. Above 10 minutes, the
time increments become longer the higher the
value.
a
The timer starts and the timer duration begins to
count down after a few seconds.
a
An audible signal sounds and the timer duration is
zero in the display when the timer duration has
elapsed.
3. Once the timer duration has elapsed:
‒
Press any button to switch off the timer.
Changing the timer
You can change the timer duration at any time.
Requirement:
is highlighted on the display.
▶
Use the or button to change the timer duration.
a
The appliance applies the change after a few
seconds.
Cancelling the timer
You can cancel the timer duration at any time.
Requirement:
is highlighted on the display.
▶
Use the button to reset the timer duration to zero.
a After a few seconds, the appliance applies the
change and goes out.
9.3 Setting the cooking time
You can set a cooking time for operation of up to 23
hours 59 minutes.
Requirement:
The type of heating and temperature or
setting are set.
1.
Press the button repeatedly until is highlighted
in the display.
2.
Use the or button to set the cooking time.
Button Default value
10 minutes
30 minutes
The cooking time can be set in 1-minute increments
up to 1 hour, and then in 5-minute increments.
a
The appliance starts heating and the cooking time
counts down after a few seconds.
a
If the cooking time has elapsed, an audible signal
sounds and the display shows the cooking time as
zero.
3.
When the cooking time has elapsed:
‒
Press any button to end the audible signal before
it sounds.
‒
To set a cooking time again, press the button.
‒
When your food is ready, switch off the appli-
ance.
Changing the cooking time
You can change the cooking time at any time.
Requirement:
is highlighted on the display.
▶
Change the cooking time using the or button.
a
The appliance applies the change after a few
seconds.
Cancelling the cooking time
You can cancel the cooking time at any time.
Requirement:
is highlighted on the display.
▶
Reset the cooking time to zero using the button.
a After a few seconds, the appliance applies the
change and continues to heat without a cooking
time.
9.4 Setting the end time
You can delay the time at which cooking is due to fin-
ish by up to 23 hours and 59 minutes.
Notes
¡
In order to achieve a good cooking result, do not
delay the end time once the appliance is already in
operation.
¡
Food will spoil if you leave it in the oven cavity too
long.
Requirements
¡
The type of heating and temperature or setting are
set.
¡
A cooking time is set.
1. Press the button repeatedly until is highlighted
in the display.
2. Press the or button.
a
The display shows the calculated end time.
3. Use the or button to delay the end time.
a
After a few seconds, the appliance applies the set-
ting and the display shows the set end time.
a
Once the calculated start time has been reached,
the appliance starts heating up and the cooking
time starts counting down.
a Once the time has elapsed, an audible signal
sounds and the display shows the cooking time as
zero.
4.
When the cooking time has elapsed:
‒
Press any button to end the signal prematurely.
‒
To set another cooking time, press the button.
‒
When your food is ready, switch off the appli-
ance.
Changing the end time
In order to achieve a good cooking result, you can only
change the set end time before operation starts and
the cooking time starts counting down.
Requirement:
is highlighted on the display.
▶
Use the or button to delay the end time.
a
The appliance applies the change after a few
seconds.
Cancelling the end time
You can delete the set end at any time.
Requirement:
is highlighted on the display.
▶
Reset the end time to the current time plus the set
cooking time using the button.
a
After a few seconds, the appliance applies the
change and starts heating up. The cooking time
counts down.
9.5 Setting the time on the clock
Once the appliance has been connected to the mains
or following a power failure, the time flashes on the dis-
play. The time starts at "12:00". Set the current time.
Requirement:
The function selector must be set to the
"Off" position ⁠.
1.
Use the or button to set the time.