Siemens Hicom 150 E Office Скачать руководство пользователя страница 95

Страница: 95 / 130

Installing the Hardware

Pin Assignments

Two 8-pin and two 6-pin modular phone jacks are located on the
back of the U

P0/E

PCI card:

Jack SYS (8-pin): Connection to Hicom 150 E Office (the two
center pins 4 and 5 are the U

P0/E

(Digital station port) lines to

the Hicom system)

Jack HA (8-pin): Port for handset cradle and handset

Jack OUT (6-pin): Port for external recording equipment

Jack IN (6-pin): Not used

In addition, one yellow LED and one red LED are on the back of the
card to indicate the following U

P0/E

PCI card statuses:

Red LED illuminated: Card error

Yellow LED flashing: Card in operation

Yellow LED illuminated: Data being transferred between card
and Hicom system

Содержание Hicom 150 E Office



































































































































Результаты поиска

Содержание Hicom 150 E Office

Отзывы:

Похожие инструкции для Hicom 150 E Office

Бренды по названию

Популярные бренды

Siemens Hicom 150 E Office, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание Hicom 150 E Office

Отзывы:

Похожие инструкции для Hicom 150 E Office

Бренды по названию

Популярные бренды