Siemens Hicom 150 E Office Скачать руководство пользователя страница 66

Страница: 66 / 130

Forwarding Calls

You can forward both internal and external calls to various destina-
tions (internal or external telephones) (whether external destination
is possible depends on system configuration).

Activating Call Forwarding

The following dialog box is displayed:

Call forwarding is activated and the call forwarding icon

appears

in the system bar.

Click the call forwarding button in the toolbar.

Enter the station number of the call forwarding destination (internal
or external telephone) and click OK to confirm your entry.

If you activate call forwarding during a call and another call
is currently waiting (call waiting), the waiting call is forward-
ed.

Содержание Hicom 150 E Office



































































































































Результаты поиска

Содержание Hicom 150 E Office

Отзывы:

Похожие инструкции для Hicom 150 E Office

Бренды по названию

Популярные бренды

Siemens Hicom 150 E Office, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание Hicom 150 E Office

Отзывы:

Похожие инструкции для Hicom 150 E Office

Бренды по названию

Популярные бренды