Siemens Hicom 150 E Office Скачать руководство пользователя страница 63

Страница: 63 / 130

Reaching Parties More Effectively

Releasing an External Trunk

You want to place an urgent external call and receive a busy signal
because no external trunk is available. You can select a busy trunk
and disconnect the call on this trunk to make the trunk available for
your call.

Releasing a Busy Trunk

You wish to dial an external station number but already hear a busy
signal before you dial.

The call display is replaced by the dialog box for releasing a trunk.

Using the

and

buttons, you can select and release

an external trunk from a menu.

Click the Back button in the box for releasing a trunk to return to the
call display.

Click the release trunk icon in the toolbar.

Now enter the station number and press Enter to confirm your en-
try. The station is dialed via the released trunk.

If your system is not configured for releasing an external
trunk, the release trunk button will not appear in the toolbar.

Содержание Hicom 150 E Office



































































































































Результаты поиска

Содержание Hicom 150 E Office

Отзывы:

Похожие инструкции для Hicom 150 E Office

Бренды по названию

Популярные бренды

Siemens Hicom 150 E Office, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание Hicom 150 E Office

Отзывы:

Похожие инструкции для Hicom 150 E Office

Бренды по названию

Популярные бренды