Siemens Gigaset DL500A Скачать руководство пользователя

Страница: 75 / 136

Connecting/using other devices

Gigaset DL500A / GRC EN / A31008-N3103-T101-1-7619 / HS_and_other_Devices.fm / 31.08.10

rsion 4, 16.0

.2005

De-registering handsets

On the base:

Registration

De-register Handset

The list of registered devices (internal par-
ties) is displayed.

Select the internal party you
wish to deregister and press

§OK§

Enter the current system PIN if
necessary and press

§OK§

§Yes§

Press the display key to confirm
the prompt.

The handset is deregistered immediately,
even if it is not in idle status.

Locating a handset (paging)

You can use the base to search for the regis-
tered handsets.

Prerequisite:

There are internal parties reg-

istered on the base. There are a maximum of
two connections between the internal par-
ties.

Open the list of internal parties.
Your own entry in the list is
marked with a < symbol.

Find handset

Select and press

§OK§

All reachable handsets ring simultaneously
("paging"), even if the ringers are deacti-
vated.

An external call will not interrupt the paging
process.

Ending paging

Press the red end key

or pick up/

replace the receiver.

You can end the paging call prematurely by
pressing the talk or end call key on one of
the handsets.

The paging call ends automatically after
approx. 30 seconds.

Making internal calls

Internal calls using registered handsets are
free of charge.

Calling a specific handset

Initiate internal call.

Enter the number of the internal
party.

If the receiver is replaced, the base switches
to handsfree mode.

Or:

Initiate internal call.

Select the internal party.

Pick up the receiver.

If the internal party cannot be reached
(e.g., out of range) or does not answer,
or three internal connections are already
established, the busy tone sounds.

Calling all internal parties
("group call")

Press and hold left on the con-
trol key.

All handsets are called.

Or:

Initiate internal call.

Press the star key.

Or:

Initiate internal call.

Call All

Select

Pick up the receiver.

All handsets are called.

If no internal parties can be reached or three
internal connections have already been
established, the busy tone sounds.

Ending a call

Replace the receiver.

Содержание Gigaset DL500A









































































































































Результаты поиска

Содержание Gigaset DL500A

Отзывы:

Похожие инструкции для Gigaset DL500A

Бренды по названию

Популярные бренды

Siemens Gigaset DL500A, Руководство пользователя

Результаты поиска

Содержание Gigaset DL500A

Отзывы:

Похожие инструкции для Gigaset DL500A

Бренды по названию

Популярные бренды