Siemens FST020 Скачать руководство пользователя страница 184

Страница: 184 / 194

Security

6.4 PIN recovery

FST020 Function manual

182

Function Manual, 09/2017, A5E42949526-AA

6.4

PIN recovery

Used to enter PIN unlock key (PUK) which resets device PIN(s) to default. (PUK obtained

from Siemens customer support.)

Setting
Default

Path

Security

→

Access management

→

PUK

6.5

Activate user PIN

Description
The Enable access level control function can be configured.

Setting Disable; Enable
Default Enable

Path

Security

→

Access management

→

Enable access level control

6.6

Deactivate user PIN

Description
The Disable access level control function can be configured.

Setting Disable; Enable
Default Enable

Path

Security

→

Access management

→

Disable access level control

6.7

Auto logout

Description
The Auto logout function can be configured. When the parameter is set to Off (default), you

will not be prompted for password for 10 minutes after the last key press. When the

Содержание FST020



































































































































































































Результаты поиска

Содержание FST020

Отзывы:

Siemens FST020, Руководство по эксплуатации функций, Страница: 184 / 194

Результаты поиска

Содержание FST020

Отзывы: