Siemens FST020 Скачать руководство пользователя страница 177

Страница: 177 / 194

Communication

5.2 Modbus (Channel 1)

FST020 Function manual
Function Manual, 09/2017, A5E42949526-AA

175

Path

Communication

→

Modbus (Channel 1)

→

Baudrate

5.2.4

Parity / framing

Description
Parity and framing of the Modbus communication interface.

Setting Even parity, 1 stop; Odd parity, 1 stop; No parity, 2 stop
Default

Path

Communication

→

Modbus (Channel 1)

→

Parity / framing

5.2.5

Floating point byte order

Description
The floating-point number byte order used within the data filed of Modbus messages,
The first mentioned byte is the first byte sent.

Byte 3 corresponds to the left-most byte (MSB) of a 32 bit floating-byte number in big endian

format, byte 0 to the right-most byte.

Setting 1-0-3-2; 0-1-2-3; 2-3-0-1; 3-2-1-0
Default

Path

Communication

→

Modbus (Channel 1)

→

Floating point byte order

5.2.6

Integer byte order

Description
The integer byte order used in Modbus messages.
MSB = most significant byte / high byte

LSB = least significant byte / low byte

Setting MSB to LSB (big endian); LSB to MSB (little endian)
Default

Содержание FST020



































































































































































































Результаты поиска

Содержание FST020

Отзывы:

Siemens FST020, Руководство по эксплуатации функций, Страница: 177 / 194

Результаты поиска

Содержание FST020

Отзывы: