Siemens FST020 Скачать руководство пользователя страница 159

Страница: 159 / 194

Maintenance and diagnostics

4.7 SensorFlash

FST020 Function manual
Function Manual, 09/2017, A5E42949526-AA

157

4.7.4

Capacity available (read only)

Description
Free capacity of installed SensorFlash.
Shows INSERT CARD if card is not installed.

Setting
Default GB

Path

Maintenance and diagnostics

→

SensorFlash

→

Capacity available

4.7.5

Data logging

4.7.5.1

Activation

Description
Activation - turns on and off data logging activation

Setting Off; On
Default Off

Related
If this parameter is set to Enabled, the parameters Logging value 1 through Logging value 20

can be configured.

Path

Maintenance and diagnostics

→

SensorFlash

→

Data logging

→

Activation

4.7.5.2

Data logging mode

Description
Select between a momentary value or an averaged value calculated over one logging

interval.

Setting Log instantaneous, Log average value
Default Log instantaneous

Path

Maintenance and diagnostics

→

SensorFlash

→

Data logging

→

Data logging mode

Содержание FST020



































































































































































































Результаты поиска

Содержание FST020

Отзывы:

Siemens FST020, Руководство по эксплуатации функций, Страница: 159 / 194

Результаты поиска

Содержание FST020

Отзывы: