Siemens FMT-A-ADPT, Инструкция по установке

Страница: 1 / 2

Siemens Siemens
Siemens Siemens
Siemens Industry Industry
Industry Industry
Industry,,,,, Inc. Inc.
Inc. Inc.
Inc.
Building Building
Building Building Building T
TT
TTec
ec
ec ec echnologies Di
hnologies Di
hnologies Di hnologies Di hnologies Division
vision
vision vision vision
P/N 315-050338-0
Class A Riser Module for the FMT
Installation Instructions
Model FMT-A-ADPT
INTRODUCTION The Model FMT-A-ADPT module (as shown in Figure 1) from Siemens
Industry, Inc., provides the FMT with Class A riser capability. The
telephone riser is supervised by the primary FMT.
PRE-INSTALLATION The FMT-A-ADPT is shipped with the bracket for use on the CC-2 or
CC-5 Card Cages attached to the FMT-A-ADPT board.
T TT
TTo use the FMT
o use the FMT
o use the FMT o use the FMT o use the FMT-A-ADPT on a CC-2 Card Cage,
-A-ADPT on a CC-2 Card Cage,
-A-ADPT on a CC-2 Card Cage, -A-ADPT on a CC-2 Card Cage, -A-ADPT on a CC-2 Card Cage, y
y
y y you must place it in
ou must place it in
ou must place it in ou must place it in ou must place it in
Slot 1 (t Slot 1 (t Slot 1 (t Slot 1 (t Slot 1 (terminals 9-1 erminals 9-1 erminals 9-1 erminals 9-1 erminals 9-16) of the top Double Header; on a CC-5 Card 6) of the top Double Header; on a CC-5 Card 6) of the top Double Header; on a CC-5 Card 6) of the top Double Header; on a CC-5 Card 6) of the top Double Header; on a CC-5 Card
Cage y Cage y Cage y Cage y Cage you must place it in Slot 5 (t ou must place it in Slot 5 (t ou must place it in Slot 5 (t ou must place it in Slot 5 (t ou must place it in Slot 5 (terminals 9-1 erminals 9-1 erminals 9-1 erminals 9-1 erminals 9-16) of the top Double Header 6) of the top Double Header 6) of the top Double Header 6) of the top Double Header 6) of the top Double Header.....
The FMT-A-ADPT is shipped with two removable terminal plugs
(see Figures 5 and 6) that are installed in J1 and J2. Remove the
terminal plug from the CC-5/CC-2 header (terminals 9-16) where the FMT-A-ADPT will
be installed. Transfer the existing field wiring in the connector to connector J2 as
explained in the wiring section and discard the connector that was removed.
INSTALLATION
Remove all system power before installation, first battery then AC. (To power up,
connect the AC first, then the battery.)
Install the FMT-A-ADPT (Refer to Figure 2) in the top header of the CC-5/CC-2. Insert
the female plug on the end of the FMT-A-ADPT into the appropriate top header (Slot 5
J1
J4
J2
J3
(FEMALE PLUG)
FMT-A-ADPT MODULE
PLUGS INTO TOP
DOUBLE HEADER OF
SLOT 5 OF CC-5 OR
SLOT 1 OF CC-2 CARD
CAGE.
CC-5 CARD CAGE
INSTALL FMT-A-ADPT
MODULE IN SLOT 5
OF CC-5 CARD
CAGE, AS SHOWN.
FOR CC-2 CARD CAGE,
INSTALL
MODULE IN SLOT 1
AND USE THIS SPACE
FOR CAPTIVE SCREW.
FMT-A-ADPT
CC-5 TOP DOUBLE
HEADER
CAPTIVE SCREW
ANY XLS SINGLE
SLOT MODULE
CC-5 BOTTOM
HEADER
SLOT FOR CAPTIVE
SCREW IN SLOT 1 OF
CC-2 TOP DOUBLE HEADER
SLOT FOR CAPTIVE
SCREW IN SLOT 5 OF
CC-5 TOP DOUBLE HEADER
Figure 3
FMT-A-ADPT Installed in CC-5
Figure 1
FMT-A-ADPT PCB
FMT-A-ADPT
J1
J2
J3
J4
E6
E3
E7
E2
E4
E5
16 9
16
9
1
1 2 3 4 5 6 7 8
Figure 2
FMT-A-ADPT