Siemens Flender KMP Series Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 84

background image

BA 9142 en 02/2015

10.9

Vibration measurements

DANGER

Danger to life from rotating and/or moving parts

Risk of being gripped or drawn in by rotating and/or moving parts.
If a mobile vibration measurement is taken on a gear unit while it is in operation, it is imperative to ensure
that the measurement is not taken directly near rotating parts in order to avoid accidental contact with
the rotating parts.

A

3V

4V

5H

7H

6HA 8H

3V

4V

6H

3HA 4H

3H 4H

5H

"A"

Fig. 11:

Measuring points

V

Vertical measuring point

H

Horizontal measuring point

(Measuring points 1 and 2 are located at the bearing points on the motor.)

The measuring points shown in Figure 11 are the standard measuring points in a mobile measurement.
All gear units of this type in the field can be measured on these measuring points. This enables direct
comparison with other gear units of the same type and same size. A detailed illustration of the gear unit is
contained the drawings in the gear unit documentation.

Vibration measurements and their evaluation should be conducted by Siemens personnel and/or in close
collaboration with Siemens personnel. This way, experience gained from measurements conducted on
comparable bevel-gear planetary gear units can be incorporated into the measurement and the evaluation
of its results.

«
...
77
78
79
80
81
...
»

Содержание Flender KMP Series





















































































Отзывы:

Нет отзывов

Похожие инструкции для Flender KMP Series

Бренд: zipwake Страницы: 2

Бренд: zipwake Страницы: 2

Бренд: Eagle Eye Power Solutions Страницы: 2

Litmann Quality 3100

Бренд: 3M Страницы: 2

Бренд: DANLERS Страницы: 2

Бренд: Haas Automation Страницы: 26

ProFire Lightbridge

Бренд: M-Audio Страницы: 8

Бренд: M-Audio Страницы: 36

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренд: Balanced Body Страницы: 37

Бренд: Bartscher Страницы: 20

Бренд: Bartscher Страницы: 24

Бренд: H&S Страницы: 32

Бренд: Interacoustics Страницы: 25

Бренд: Hamilton Beach Commercial Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды