Siemens FDUL221 Скачать руководство пользователя страница 61

Страница: 61 / 76

Operation

Tips for troubleshooting on the detector line

Building Technologies

008250_i_en_--

Fire Safety

2013-08-15

6.14

Tips for troubleshooting on the detector line

Once the detector line has been read in, the FDUL221 line tester detects the

following detector line errors:

  Open line
  Ground fault
  Short-circuit
  Shield fault
  Shield permeability
  Shield ground fault

If a single line device is selected with the FDUL221 line tester, its internal or

external alarm indicator will flash.
If the 'All ON' is selected in the 'Locate devices' menu, the internal/external alarm

indicators of all line devices detected by the FDUL221 line tester flash. In this way,

you can detect line devices that were not detected by the FDUL221 line tester.

6.14.1

Error search using the 'bisection' method

The FDUL221 line tester is ready for operation.

1. Separate the lines on a line device in the center of the loop or stub and create

two stubs.

2. Measure each stub.

You will detect the stub with the error.

Divide the faulty stub in the center and connect the previously separated

points.

3. Measure each stub.

This will enable you to identify the area with the error.

4. Proceed as described with the division until you have located the error.

The increasingly smaller sections will enable you to rapidly locate the error.

Error search using the 'bisection' method

Содержание FDUL221













































































Результаты поиска

Содержание FDUL221

Отзывы:

Siemens FDUL221, Техническое руководство, Страница: 61 / 76

Результаты поиска

Содержание FDUL221

Отзывы: