Siemens FDCW221 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 52

background image

Commissioning

33

Building Technologies

009865_b_en_--.doc

Fire Safety & Security Systems

11.2007

8.2

Putting the radio gateway into operation

Before radio detectors can be registered on the radio gateway, the radio gateway
must be put in operation.

CAUTION

Several radio gateways use the same basis channel

Î

Radio detectors communicate with several radio gateways

Î

Faults or malfunctions may occur

z

Commissioning the radio gateways one after the other in the same
transmission field

If you want to commission several radio gateways, these must be commissioned
one after the other in the same transmission field, so that each radio gateway is
able to determine its own basis channel in configuration mode and registered radio
detectors each communicate with only one radio gateway.
Afterwards you may as well install the radio gateway in longer distances.
So you can ensure that even temporary changes of the radio detectors do not
cause any malfunctions due to the occupancy of the same basis channels.

Prerequisites:

z

The FDnet detector line must be switched off.

z

The radio gateway is in delivery condition.

z

It is not allowed to commission several radio gateways simultaneously.

Procedure:
1.

Unlock the housing cover of the radio gateway on the front side with pin and pull
it off.

2.

Insert a new battery.

Î

The radio gateway changes from startup mode to the configuration mode for
the basis channel.

Î

The red and green LED are alternatingly flashing slowly.

Î

The radio gateway looks for a free basis channel and signals the result

–

Channel found: green LED flashes slowly

–

No channel found: red LED flashes slowly

Î

The radio gateway is ready for configuration mode

When the red LED flashes twice after inserting the battery, the battery voltage is too low.

If no basis channel is found, please consult the chapter 'Maintenance / Troubleshooting'.

see also:

Î

8.3 Register the radio detector at the radio gateway, Page 34

Î

8.6 Resetting the radio gateway in delivery condition, Page 38

Î

9 Maintenance / Troubleshooting, Page 42

Î

Fig. 2 , Page 11

Î

Fig. 3 , Page 12

«
...
31
32
33
34
35
...
»

Содержание FDCW221





















































Отзывы:

Нет отзывов

Похожие инструкции для FDCW221

Бренд: Kentec Electronics Страницы: 107

Бренд: C-TEC Страницы: 2

Бренд: Zeta Страницы: 4

SILENT KNIGHT SWIFT

Бренд: Honeywell Страницы: 64

Бренд: Polon-Alfa Страницы: 129

Бренд: Autronica Страницы: 20

AutroSafe BS-310

Бренд: Autronica Страницы: 133

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды