manualshive.com logo in svg

Siemens FDCIO223, Техническое руководство

Поделиться
Скачать
Siemens FDCIO223 Скачать руководство пользователя страница 57

Commissioning

Calibrating the control line

6

57 | 72

Building Technologies

009122_h_en_--

Fire Safety

2016-05-04

6 Commissioning

The device is commissioned via the control panel. The exact procedure is

described in the control panel documentation.

NOTICE

Before commissioning the device, check that the configuration of the

inputs/outputs corresponds to the circuit.

Conduct a performance check once commissioning is complete.
Measure the current at the activated outputs.
If the input/output module is to be used for control purposes, the control lines will

need to be calibrated during commissioning.

6.1 Calibrating the control line

The input/output module must be connected correctly (inputs/outputs and

power supply).
The detector line must have been commissioned.
The input/output module must be correctly configured.
The relay must not be triggered during calibration. This is especially important

in the case of inverse controls (normal position = triggered)! Consequently,

control must be activated for calibration in the case of inverse controls!

1. Press the push button (3) on the input/output module. See the chapter

'Overview [  20]'.

The control lines will then be calibrated. Duration: approx. 4 s.

2. Check that calibration has been performed successfully.

Once calibration has been successfully completed, the input/output module

runs in normal operation.

If the calibrated resistance is outside the tolerance range, an error is indicated.

The control line will be recalibrated whenever the push button is pressed.

The line must be recalibrated with each new configuration.

Содержание FDCIO223









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды