manualshive.com logo in svg

Siemens FCT010/DSL, Руководство по эксплуатации, Страница: 167 / 180

Поделиться
Скачать
Siemens FCT010/DSL Скачать руководство пользователя страница 167

Table C-10

Maintenance 

Modbus ad‐
dress

Data type / 
Size [bytes]

Parameter

Description

Default value 
[unit]

Value 
range

Access 
level

700

Unsigned / 2 Set To Default

Reset all parameters to facto‐
ry settings

-

Enter 1 to 
reset

Write

2700

Unsigned / 4 Operating Time Total Total operating time since

first power up

0 [h]

-

Read Only

2702

Unsigned / 4 Operating Time 

Operating time since last
power up

0 [h]

-

Read Only

4088

String / 14

Firmware Time Stamp Firmware time stamp speci‐

fies the date and time when 
the sensor firmware was built

-

-

Read Only

4105

String / 32

Sensor PCBA Serial 
Number

Serial number of the sensor 
electronic

-

-

Read only

Table C-11

Device diagnostics

Modbus ad‐
dress

Data type / 
Size [bytes]

Parameter

Description

Default value 
[unit]

Value 
range

Access 
level

2756

Float / 4

Driver Current

Actual sensor driver current.
The actual driver current is 
viscosity and sensor size de‐
pendent

- [A]

0 to 0.124

Read Only

2758

Float / 4

Pick-up Amplitude 1

Actual pick-up 1 amplitude

- [V]

0 to 0 9999 Read Only

2760

Float / 4

Pick-up Amplitude 2

Actual pick-up 2 amplitude

- [V]

0 to 0 9999 Read Only

2762

Float / 4

Sensor Frequency

Actual sensor frequency

- [Hz]

0 to 1 023

Read Only

3032

Float / 4

PCB Temperature

Actual sensor electronic tem‐
perature

- [C°]

-50 to 200 

Read Only

Table C-12

Aerated flow

Modbus ad‐
dress

Data type / 
Size [bytes]

Parameter

Description

Default value 
[unit]

Value 
range

Access 
level

2200

Unsigned / 2 Aerated Flow Alarm 

Limit

Alarm limit calculated in per 
cent of accepted bad meas‐
urements.

80 [%]

0 to 99

Read / 
Write

2201

Unsigned / 2 Aerated Flow Warn‐

ing Limit

Warning limit calculated in 
per cent of accepted bad 
measurements

0 [%]

0 to 99

Read / 
Write

2202

Unsigned / 2 Measurement Sam‐

ple Time

The time period over which 
the actual percentage of bad 
measurements is calculated

5 [s]

1 to 10

Read / 
Write

Modbus communication FCT010

C.4 Modbus holding registers tables

SITRANS MASS 2100 & FC300 (FCT010/DSL)
Operating Instructions, 06/2020, A5E39788682-AB

167

Содержание FCT010/DSL





















































































































































































Отзывы:

Нет отзывов