Siemens FC300 Скачать руководство пользователя страница 189

Страница: 189 / 518

10.2.1

Sensor diagnostic events

ID/

Icons

Diagnostic

Action

Comments

SIL parameters not validated

Run the 'Safety Validation' wizard to validate the

safety-critical parameters. The device can be

put into Safe Operation mode after validation

SIL parameters not validated

Run the 'Safety Validation' wizard to validate the

safety-critical parameters. The device can be

put into Safe Operation mode after validation

SIL parameters not validated

Run the 'Safety Validation' wizard to validate the

safety-critical parameters. The device can be

put into Safe Operation mode after validation

SIL parameters not validated

Run the 'Safety Validation' wizard to validate the

safety-critical parameters. The device can be

put into Safe Operation mode after validation

Sensor supply volt. out of range Contact your local Siemens representative

Temperature measurement fault Turn off the power, wait 5 seconds and turn on

the power again. If the failure continues then

contact your local Siemens representative

Temperature measurement fault Turn off the power, wait 5 seconds and turn on

the power again. If the failure continues then

contact your local Siemens representative

Diagnosing and troubleshooting

10.2 Fault codes and corrective actions

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

189

Содержание FC300







































































































































































































































































































































































































































































































































Результаты поиска

Содержание FC300

Отзывы:

Siemens FC300, Руководство по эксплуатации, Страница: 189 / 518

Результаты поиска

Содержание FC300

Отзывы: