Siemens FC300 Скачать руководство пользователя страница 157

Страница: 157 / 518

● Standard volume flow
● Fraction A
● Fraction B

Recipes

Five recipes can be configured individually, however only one of the recipes can be active at

a time.

8.8.2

Valve control configuration

Valve control dosing

Dosing is controlled with either one or two discrete valves or a single analog valve. The

transmitter provides up to three input/output channels which can be used for dosing control.

The selection of channels is fixed when ordering the system. The channels can be setup for

dosing functionality in parameter 2.5.1 "Dosing Mode" as shown in the table below. Allocation

of the output to a specific dosing sequence element is performed in the software configuration

as follows:

One on/off valve

Configuration of one valve (primary valve).
One of the following channels must be assigned to control the discrete primary valve.

Table 8-1

One on/off valve

Valve control

Channel HW con‐

figuration

Output

channel

Channel SW configuration
Menu item

Value

Discrete valve con‐

trol - Primary Valve

Signal output

2.4.2.1

"Operation Mode"

Status Output

2.4.2.27

"Status Mode"

Primary Valve Dosing

2.4.3.1

"Operation Mode"

Status Output

2.4.3.29

"Status Mode"

Primary Valve Dosing

2.4.6.1

"Operation Mode"

Status Output

2.4.6.27

"Status Mode"

Primary Valve Dosing

Relay output

2.4.4.1

"Status Mode"

Primary Valve Dosing

2.4.7.1

"Status Mode"

Primary Valve Dosing

Two on/off valves

Configuration of two valves (primary and secondary valves)

Functions

8.8 Dosing

MASS 2100 & FC300 (FCT030)

Operating Instructions, 06/2017, A5E39789040-AA

157

Содержание FC300







































































































































































































































































































































































































































































































































Результаты поиска

Содержание FC300

Отзывы:

Siemens FC300, Руководство по эксплуатации, Страница: 157 / 518

Результаты поиска

Содержание FC300

Отзывы: