Siemens FC121-ZA Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 90

background image

55

Smart Infrastructure

A6V10393190_h_en_--

2019-09-01

7

Programming

For programming, access level 3 is required.

All outputs are automatically isolated during programming mode.
All disabled outputs are automatically enabled if access level 2 is reached.

7.1

Configure

7.1.1

Zone

Configure parameter for each zone.

Select a zone for programming.

Standard

Automatic detectors
and manual call
points can be mixed
within the same
zone.
Device could be
either conventional
or collective.

AVC option
'1', '2'

Mixed MCP & det.

AVC option
'1', '2', '3'

GB continuity

If detectors are removed, the
zone will work properly.

Short = alarm

Any short is detected as 'Fire
Alarm'.

Direct

'1'

No delay, immediate alarm.

Via V1 / V2

'2'

Delayed alarm.

V1: reaction time, 3 min.
V2: investigation time, 5 min.

(Change value, see
chapter 7.2.10).

Via AVC timer
MCP direct

'3'

- Delayed alarm for automatic

detectors.

- No delay for MCPs.

If selected, the 'Alarm' state is achieved, if the second device activation in the same zone
occurs within 90 seconds. The first device activation is inhibited from the zone and
automatically reset after a defined time, (default value: 15 second, see chapter 7.2.5).

If selected, the 'Alarm' state is achieved, if the second corresponding zone is in 'Alarm' as well.
The zone pairs (1&2, 3&4, 5&6, etc) are predefined in the system,

e.g. if zone 6 is selected, zone 5 is automatically linked as well and vice versa.

Name the zone, see chapter 7.5.

*Do NOT use this function in combination with FDOOT241-9 (ES<13). For detailed
information refer to document A6V10393192.

Customer

text

Zone

coincidence

*Device

coincidence

AVC

Mode

Zone 1..n

Zone

Accessory

card(s)

Input

Output

Zone

Configure

«
...
53
54
55
56
57
...
»

Содержание FC121-ZA



























































































Отзывы:

Нет отзывов

Похожие инструкции для FC121-ZA

Бренд: OmarLift Страницы: 14

Бренд: Panasonic Страницы: 16

Бренд: GARAN Страницы: 8

Бренд: Gamma Vacuum Страницы: 25

Бренд: Gamma Страницы: 28

Digiplex DGP-848

Бренд: Paradox Страницы: 20

Бренд: RADEMACHER Страницы: 48

MicroTech II UV05

Бренд: AAF Страницы: 50

Red Atom PETRA01

Бренд: Perenio Страницы: 24

Бренд: Game ready Страницы: 24

S3500 Series Uplink Module

Бренд: Aruba Страницы: 8

Бренд: Lutron Electronics Страницы: 2

Бренд: Wavelength Electronics Страницы: 17

Бренд: KWC Страницы: 8

Arteor 5 742 74

Бренд: LEGRAND Страницы: 2

Бренд: HTW Страницы: 88

Бренд: Powtran Страницы: 40

Бренд: Omega Engineering Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды