Siemens EX8 LX3 E Series Скачать руководство пользователя страница 15

Страница: 15 / 52

Operating the appliance

Note:

When you switch on the ventilation system, the

right-hand settings area is no longer available. You can

change the fan setting for the ventilation system in the

left-hand settings area.

Switching on the ventilation system

Note:

If the

and

symbols are not available, insert

the metal grease filter correctly.

The

and

symbols are available. The ventilation

system can be switched on.

Touch the

symbol.

The ventilation system starts at fan setting

. The

setting that is selected will be shown on the display

panel and in the left-hand settings area. The right-

hand settings area is not available.

Notes

– Heat settings cannot be changed while the

setting is being applied for the ventilation system.

– During a period of a few seconds, a fan setting

for the ventilation system can be selected. The

settings area can then be used for selecting the

heat settings again.

Select the required setting from the settings area.

The setting that is selected will be displayed in the

left-hand settings area.

To set a different setting, touch the

symbol and

select the required setting from the settings area.

The setting that is selected will be displayed in the

left-hand settings area.

Switching off the ventilation system

If you want to switch off the appliance, touch the

symbol. If you only want to switch off the ventilation

system, proceed as follows:

Touch the

symbol.

Select the

‹

symbol in the settings area.

Touch the

symbol to switch to the setting area for

the hob.

Note:

The run-on will start once the appliance has been

switched off (depending on the basic settings selected).

Intensive setting

Activate intensive mode if strong odours or large

amounts of steam are produced. In this mode, the

ventilation system briefly operates at maximum power. It

automatically switches back to a low setting after a

short time.

Switching on

Touch the

symbol.

Touch the

›

symbol.

The

›

symbol and the symbols in the left-hand settings

area will be lit.

›

is shown on the display panel.

Intensive mode is now activated.

Note:

After eight minutes, the appliance automatically

switches back to fan setting

Note:

After a few seconds, the settings area for the heat

settings will be displayed again.

Switching off

Touch the

symbol.

In the next few seconds, slide your finger over the

settings area until setting

‹

or another setting is

displayed.

Automatic start

Depending on the basic settings selected, the following

options will be available once you have selected the fan

setting for a cooking zone:

■

The ventilation system will not start.

■

The ventilation system will start at the fan setting

selected by the sensor.

■

The ventilation will start at a specified fan setting.

Select the option you want to use in the basic settings.

The basic settings also offer the option to adjust the

sensitivity of the sensor.

"Basic settings"

on page 36

Automatic mode with sensor control

Switching on

Touch the

symbol.

The optimum setting is set automatically using a sensor.

‘

will be shown on the display panel.

Switching off

Touch the

symbol.

The fan setting that was last selected by the sensor will

be shown on the display panel. Automatic mode is

switched off.

Содержание EX8 LX3 E Series





















































Результаты поиска

Содержание EX8 LX3 E Series

Отзывы:

Похожие инструкции для EX8 LX3 E Series

Бренды по названию

Популярные бренды

Siemens EX8 LX3 E Series, Инструкция по эксплуатации

Результаты поиска

Содержание EX8 LX3 E Series

Отзывы:

Похожие инструкции для EX8 LX3 E Series

Бренды по названию

Популярные бренды