manualshive.com logo in svg

Siemens ERTEC 200P, Руководство пользователя

Siemens ERTEC 200P - это передовой сетевой коммутатор с поддержкой множества функций. Здесь вы можете бесплатно скачать руководство по эксплуатации для этого устройства. Посетите наш сайт manualshive.com, чтобы получить доступ к руководству в формате PDF.

Поделиться
Скачать
background image

 
 

 

Copyright © Siemens AG 2016. All rights reserved 

117 

ERTEC 200P-2 Manual 

Technical data subject to change 

 

Version  1.0 

 

The GDMA RAM has additionaly EDC bits (7 Bit for a 32Bit word, 1Bit error correctable, 
2Bit error recognizable). If an EDC error is detected, in the SCRB Register 'EDC_EVENT' 
(see chap. 2.3.10.9.22

X

) the appropriate reason is stored (GDMA-1B: 1Bit-Error corrected 

or GDMA-2B: 2Bit-Error recognized) and the Interrupt 'EDC_Event' IRQ48 is generated 
(see chap. 2.3.2.14). The EDC Event Register is reseted by writing the register with '0h'.  
After reset the initialisation of the EDC-Bits isn't done by hardware. This must be done by 
software. After this initialisation the SW must finally set 'GDMA_INIT_DONE = 1b'in the 
SCRB-Register 'EDC_INIT_DONE' (see chap. 2.3.10.9.22

X

). 

 

2.3.4.1.7 Interrupts 

The DMA controller has two interrupt request outputs. These signals are high active 
pulse. The length of the interrupt request pulse is at least 2 and at most 5 AHB clock 
cycles.  
The GDMA controller incorporates no local interrupt controller of its own.  
The two interrupt requests are: 
DMA Interrupt Request (DMA_IRQ) - generated in the following cases: 

  Job is finished and bit “Interrupt Request Generation Enable” (INTR_EN) in the 

Job Control register is set to “1”. When Interrupt request is generated, a “job fin-
ished” bit is set in the Interrupt State register (GDMA_IRQ_STATUS). This status 
register must be read by the interrupt controller to figure out which job has caused 
the interrupt. The register is cleared by writing a “1” to the related bit position. 

  A monitored error occurs at the DMA controller and bit “Error Interrupt Enable” 

(ERR_INT_EN) in the GDMA Main Control register is set to “1”. In this case the 
relevant error bit in the GDMA Error Interrupt State register is set to “1”. This status 
register must be read by the interrupt controller to figure out which type of error 
has caused the interrupt. The register is cleared by writing a “1” to the related bit 
position. 

The monitored types of error are: 

  DMA Destination Address error - Assumed when a wrong destination address, 

pointing to the DMA registers or the DMA RAM, is programmed. The relevant error 
bit in the GDMA_ERR_IRQ_STATUS register is ERR_DST_ADDR. 

  AHB Master Interface error - Assumed when an error response occurs at the AHB 

Master 

Interface.  

The relevant error bit in the GDMA_ERR_IRQ_STATUS register is ERR_AHB. 

  HW Job Start error - Assumed when HW starts a job again, before it is finished. 

The  relevant error bit  in  the  GDMA_ERR_IRQ_STATUS register  is 
ERR_JOB_START. 

 

Not allowed write access to the AHB Slave - Assumed when a different transfer 
size other than Word is used during a write access. The relevant error bit in the 
GDMA_ERR_IRQ_STATUS register is ERR_AHBSLV_WRITE.

 

2.3.4.2  ERTEC 200P GDMA Use Cases 

2.3.4.2.1 Using the Job Start and HW_REQ Signal List 

There are 2 ways to implement a HW-triggered DMA transfer. 

 

Содержание ERTEC 200P






















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ERTEC 200P

FAAC E550 Manual preview
E550
Бренд: FAAC Страницы: 12
Saitek P880 User Manual preview
P880
Бренд: Saitek Страницы: 44
Ebyte E70 Series User Manual preview
E70 Series
Бренд: Ebyte Страницы: 34
XVision XD200 User Manual preview
XD200
Бренд: XVision Страницы: 28
YASKAWA CC-Link Installation Manual preview
CC-Link
Бренд: YASKAWA Страницы: 61
Samsung DMS2.5 Service Manual preview
DMS2.5
Бренд: Samsung Страницы: 32
Eaton A201 Instruction Leaflet preview
A201
Бренд: Eaton Страницы: 6
Veeder-Root TLS Install, Setup, & Operation Manual preview
TLS
Бренд: Veeder-Root Страницы: 27
Valve Concepts 1078 Installation, Operation And Maintenance Manual preview
1078
Бренд: Valve Concepts Страницы: 18
K&K M1500 Installation Instructions Manual preview
M1500
Бренд: K&K Страницы: 6
Game ready Equine 550250 User Manual preview
Equine 550250
Бренд: Game ready Страницы: 24
Danfoss ChangeOver6 Operating Manual preview
ChangeOver6
Бренд: Danfoss Страницы: 2
MX Atmos Sigma Fitting Instructions Manual preview
Atmos Sigma
Бренд: MX Страницы: 12
National Instruments SCXI-1181K Installation Manual preview
SCXI-1181K
Бренд: National Instruments Страницы: 4
Rare Waves Grendel 2TAC Manual preview
Grendel 2TAC
Бренд: Rare Waves Страницы: 18
Brooks 5866 Installation And Operation Manual preview
5866
Бренд: Brooks Страницы: 66
nano sensorics TEMPHU Operation And Installation Manual preview
TEMPHU
Бренд: nano sensorics Страницы: 6
NCD ZigBee ZSCAN16 MIRROR Manual preview
ZigBee ZSCAN16 MIRROR
Бренд: NCD Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды