Siemens Drager medical Carina Скачать руководство пользователя страница 35

Страница: 35 / 144

Instructions for Use Carina SW 3.n

Preparation

Attach universal bracket with standard rail

Attach right side of holder to right side of
column.

Make sure the nose of the universal bracket is
completely behind the revolving edge.

Attach the left side of the holder to the left side
of the column. Make sure the nose of the uni-
versal bracket is completely behind the revolv-
ing edge.

For level adjustment use the plate on the upper
side of the universal bracket.

Level the universal bracket.

Secure adjusting lever.

Height Adjustment
5

Release adjusting lever and adjust height of
universal bracket.

Level universal bracket.

Retighten adjusting lever.

Attaching accessories to the standard rail

Attach accessory to the standard rail. Observe
the maximum payload! See "Trolley" on
page 118.

CAUTION

Check tension of universal bracket: The universal
bracket must be securely seated on the column.
Otherwise the universal bracket may loosen.

086

087

088

Содержание Drager medical Carina

















































































































































Результаты поиска

Содержание Drager medical Carina

Отзывы:

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 35 / 144

Результаты поиска

Содержание Drager medical Carina

Отзывы: