manualshive.com logo in svg

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 136 / 144

Поделиться
Скачать
Siemens Drager medical Carina Скачать руководство пользователя страница 136

Description

136

Instructions for Use Carina SW 3.n

Using invasive ventilation with VentStar Carina 
ExpV (MP 00 313)

This hose system has an expiratory valve. There-
fore the exhaled gas runs through the expiratory 
valve instead of the inspiratory limb when the 
device is not operating.

Mask ventilation (Non-invasive 
ventilation)

NIV (the mask ventilation) 

In combination with the VentStar Carina LeakV 
(MP 00 312) and the full-face mask or the total-face 
mask, the user must use a non-vented (non-anti-
asphyxia valve) connector to the mask.

With mask ventilation/non-invasive ventilation 
Carina provides a mode which is specifically 
designed for non-invasive ventilation with a nose or 
face mask. In non-invasive ventilation there are 
usually larger leaks than in tube ventilation. For this 
reason the automatic leak compensation trigger 
recognition is matched to these special condi-
tions.The alarm and monitoring concept calls for 
greater attention on the part of the user.

WARNING
The full-face mask, which covers the entire 
nose and mouth or the total-face mask, which 
covers the entire face, should not be used on 
patients who are uncooperative, obtunded, 
unresponsive, or unable to remove the mask. 
There is a risk of CO

2

 re-breathing in case of a 

device failure. Danger for the patient!

Содержание Drager medical Carina

















































































































































Отзывы:

Нет отзывов