Siemens Drager medical Carina Скачать руководство пользователя страница 123

Страница: 123 / 144

Instructions for Use Carina SW 3.n

123

Technical Data

Recommended separation distances

Recommended separation distances between port-
able and mobile RF-telecommunication devices
and the Carina.

Information regarding separation distances
(IEC 60601-1-2: 2001, table 205 and 206)

Max. P

EIRP

(W)

3 V/m distance

(m)

3 V/m distances to transmitters with frequencies from 150 kHz to 2.5 GHz, otherwise 1 V/m distance.

1 V/m distance

(m) Examples

0.001

0.06

0.17

0.003

0.10

0.30

0.010

0.18

0.55

0.030

0.32

0.95

e.g. WLAN 5250/ 5775 (Europe)

0.100

0.58

1.73

e.g. WLAN 2440 (Europe), Bluetooth

0.200

0.82

2.46

e.g. 5250 (not in Europe)

0.250

0.91

2.75

e.g. DECT devices

1.000

1.83

5.48

e.g. GSM 1800-/ GSM 1900-/ UMTS-
mobiles, WLAN 5600 (not in Europe)

2.000

2.60

7.78

e.g. GSM 900 mobiles

3.000

3.16

9.49

10.000

5.80

17.30

100.000

18.30

54.80

Содержание Drager medical Carina

















































































































































Результаты поиска

Содержание Drager medical Carina

Отзывы:

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 123 / 144

Результаты поиска

Содержание Drager medical Carina

Отзывы: