manualshive.com logo in svg

Siemens Drager medical Carina, Инструкция по эксплуатации, Страница: 121 / 144

Поделиться
Скачать
Siemens Drager medical Carina Скачать руководство пользователя страница 121

Instructions for Use Carina SW 3.n

121

Technical Data

Electromagnetic emissions

Carina is intended for use in the electromagnetic 
environment specified below. The customer or the 
user of the Carina should assure that it is used in 
such an environment.

Information regarding electromagnetic emissions 
(IEC 60601-1-2: 2001, table 201) 

Electromagnetic immunity

Carina is intended for use in the electromagnetic 
environment specified below. The customer or the 
user of the Carina should assure that it is used in 
such an environment.

Emissions

Compliance according to 

Electromagnetic environment

Radio frequency emission 
(CISPR 11)

Group 1

Carina uses RF energy only for its 
internal function. Therefore, its 
RF emissions are very low and are 
not likely to cause any interference in 
nearby electronic equipment.

Class B

Carina is suitable for use in all estab-
lishments, including domestic estab-
lishments and those directly 
connected to the public low-voltage 
power supply network that supplies 
buildings used for domestic pur-
poses.

Harmonic emissions 
(IEC 61000-3-2)

Class A

Voltage fluctuations/flicker 
(IEC 61000-3-3)

Complies

Immunity against

IEC 60601-1-2 
test level

Compliance 
level 
(of Carina)

Electromagnetic environment

Electrostatic discharge 
(IEC 61000-4-2)

Contact discharge: 
±6 kV 

±8 kV

Floors should be wood, concrete or 
ceramic tile. If floors are covered with 
synthetic material, the relative humid-
ity should be at least 30 %.

Air discharge: 
±8 kV

±15 kV

Electrical fast transient/
bursts (IEC 61000-4-4)

Power supply 
lines: ±2 kV 

±2 kV

Mains power quality should be that of 
a typical commercial or hospital envi-
ronment.

Longer input/ out-
put lines: ±1 kV

±1 kV

Surge on AC mains lines 
(IEC 61000-4-5)

Common mode: 
±2 kV

±2 kV

Mains power quality should be that of 
a typical commercial or hospital envi-
ronment.

Differential mode: 
±1 kV

±1 kV

Содержание Drager medical Carina

















































































































































Отзывы:

Нет отзывов