Siemens CP 1243-8 IRC Скачать руководство пользователя страница 29

Страница: 29 / 140

CP 1243-8 IRC
Operating Instructions, 06/2015, C79000-G8976-C385-01

LEDs and connectors

2.1

Opening the covers of the housing

Location of the display elements and the electrical connectors

The LEDs for the detailed display of the module statuses are located behind the upper cover

of the module housing.
The Ethernet connector is located behind the lower hinged cover of the module.

Opening the covers of the housing

Open the upper or lower cover of the housing by pulling it down or up as shown by the

arrows in the illustration. The covers extend beyond the housing to give you a grip.

Figure 2-1

Opening the covers of the housing

Содержание CP 1243-8 IRC













































































































































Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание CP 1243-8 IRC

Отзывы:

Похожие инструкции для CP 1243-8 IRC

Бренды по названию

Популярные бренды